High fiber count MTP® Elite Male trunk cable with 48 Fibers (Base-12), OM4 50/125μm and Plenum (OFNP) jacket. The double jacket construction protects the breakout legs during installation, and every leg is labeled and tested before the cable leaves our factory.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP® Elite Male (Pinned) to MTP® Elite Male (Pinned), 48 Fibers (Base-12)
- OM4 50/125μm, bend insensitive fiber
- Insertion loss ≤0.20dB, return loss ≥27dB
- Type B polarity
- 8.5-9.0mm Plenum (OFNP) round cable
- Minimum bend radius 7.5mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | 48FMTPOM4 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Male (Pinned) |
| Connector B | US Conec MTP® Elite Male (Pinned) |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | UPC to UPC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 48 Fibers (Base-12) |
| Glass Fiber | Bend Insensitive Fiber |
| Cable Structure | Double Jacket |
| Minimum Bend Radius | 7.5mm |
| Cable Outside Diameter (OD) | 8.5-9.0mm |
| Breakout Outside Diameter (OD) | 2.0mm |
| Breakout Length | 0.84m |
| Long-term Tensile Load | 200N |
| Short-term Tensile Load | 660N |
| Insertion Loss | ≤0.20dB |
| Return Loss | ≥27dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
Backbone cabling is where mistakes cost the most, so this trunk is built and verified entirely in the factory. The 48 Fibers (Base-12) construction concentrates the equivalent of many duplex jumpers into a single assembly, which is exactly what high density spine and leaf cabling needs. It arrives with test results, labeled legs and the correct polarity for your panel layout.
Trunk Construction and Polarity
The trunk uses a double jacket design: a rugged outer sheath protects the whole bundle, while each breakout leg keeps its own jacket and numbering. Base-8 and Base-12 constructions are available depending on the fiber count. Polarity follows the Type shown in the table, and pulling eyes or mesh grips can be fitted for installation.
Ordering Information
Ordering is simple: send us 48FMTPOM4 and your required lengths and quantities, and we return a factory quote the same working day. The 1m (3ft) version is the standard model; Small trial orders are welcome before you commit to a full project rollout.
Logistics
Standard configurations normally ship within a few working days by DHL, UPS, FedEx, TNT or EMS. For project quantities we arrange air or sea freight, and we can ship on your own courier account or deliver to your appointed forwarder.
How We Pack
Every cable is protected with dust caps and individual packaging before being boxed for shipment. Batch test reports and your own part number labels can be included in each bag.
Built to Your Spec
As a factory we can modify almost every detail of this product: length, jacket material and color, polarity, gender, breakout geometry, labeling and packaging. Non-standard variants are routine work for us, not a special project.
