Dell (Force10) CBL-10GSFP-DAC-6M Compatible 10G SFP+ Passive Copper Twinax Cable, 6m (20ft)

Product Highlights

• Compatible alternative to Dell (Force10) CBL-10GSFP-DAC-6M
• 10G connectivity at 10Gbps
• Interface configuration: SFP+ to SFP+
• Fixed length and part number: 6m (20ft), (Force10) CBL-10GSFP-DAC-6M
• Cable construction: Passive Twinax
• Conductor specification: 24AWG
• Maximum power consumption: ≤0.1W
• Minimum bend radius: 30mm

Specifications

Power and Thermal Planning

The rated power consumption is ≤0.1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Rack Layout and Service Access

Plan the managed route before removing the connector protection. The cable should reach both ports without tension while leaving enough space to release the latches and service adjacent interfaces. Support the run through the intended managers, keep the connector boots clear of sharp edges and avoid storing excess length in a tight coil behind warm exhaust air. For this assembly, the listed conductor specification is 24AWG; the minimum bend radius is 30mm; the stated power consumption is ≤0.1W; the jacket material is PVC (OFNR).

Cable Construction and Routing

This assembly uses 24AWG conductors, PVC (OFNR) jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is 10G Ethernet. Listed interface and protocol references include 1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

Passive Copper Operation

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

Length Selection and Installation Planning

The installation review for a 6m (20ft) link should include pathway length, support points, connector access and future maintenance. Route the complete copper assembly and both connector housings before attaching both ends, and avoid dragging it across connector panels. A final inspection should confirm that no latch, boot or jacket section carries unnecessary strain. Within this family, (Force10) CBL-10GSFP-DAC-5M is shorter at 5m (16ft), while (Force10) CBL-10GSFP-DAC-7M is the next longer choice at 7m (23ft); comparing those two boundaries helps avoid both tension and unnecessary slack.

Position Within the Length Range

(Force10) CBL-10GSFP-DAC-6M occupies the middle of this family between (Force10) CBL-10GSFP-DAC-5M at 5m (16ft) and (Force10) CBL-10GSFP-DAC-7M at 7m (23ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Quality Assurance and Packaging

The completed cable is inspected at both ends, functionally tested and coiled with bend-safe slack. Protective packaging keeps the latches and boots from taking impact, while optional project labels can identify the two endpoint locations for easier field service. Volume orders can include customer references on the labels and carton list.

Dell Compatibility and Factory Testing

Compatibility is verified as part of a complete installation check: connector inspection, host identification and an operating link. The physical cable is evaluated together with the expected OEM identity, because a connector that fits is not sufficient evidence that the host will accept and operate the assembly correctly. The check includes link stability and diagnostic indications, followed by a final inspection of both ends.

Frequently Asked Questions

Ordering Information

When requesting this assembly, include the exact part number and length together with the destination port types. For a rack installation, a simple port-to-port list helps us keep different lengths separate and allows any requested labels to correspond with the actual installation sequence. This page’s fixed configuration is 6m (20ft); another length must be quoted under its corresponding part number.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.