Mellanox QSFP-200G-2QACxxx Compatible Customized 200G QSFP56 to 2 x QSFP56 Active Copper Breakout Cable

Product Highlights

• HT-manufactured compatible alternative for Mellanox QSFP-200G-2QACxxx
• 200G aggregate connectivity at 200Gbps
• Interface configuration: QSFP56 to 2× QSFP56
• Active Twinax
• Length configurations covered: Customized
• Conductor specification: 30AWG for 3m 28AWG for 5m 26AWG for 7m
• Power consumption: 1.5W
• Operating temperature: 0 to 70°C (32 to 158°F)

Available Lengths and Corresponding Part Numbers

The documented series configuration is Customized. Use the relevant OEM reference below together with the HT identity and required length when requesting a quotation. If another length carries a different OEM part number, it must be reviewed and ordered as that distinct configuration.

Compatible OEM Part Numbers

• QSFP-200G-2QACxxx

Specifications

Rack Layout and Service Access

Plan the managed route before removing the connector protection. The cable should reach both ports without tension while leaving enough space to release the latches and service adjacent interfaces. Support the run through the intended managers, keep the connector boots clear of sharp edges and avoid storing excess length in a tight coil behind warm exhaust air. For this series, keep the interface rate, ACC construction and length-specific OEM reference together throughout that review.

Applications and Deployment

Active copper assemblies add signal conditioning while retaining the convenience of a direct-attached cable. They are appropriate where the equipment supports the stated active-cable type and the route exceeds the practical limits of a comparable passive assembly. Per-end power, airflow and host qualification should be assessed before high-density deployment. For this series, the listed interface is QSFP56 to 2× QSFP56 and the aggregate rate is 200G.

Cable Construction and Routing

The specification table records the conductor specification is 30AWG for 3m 28AWG for 5m 26AWG for 7m; the jacket material is PVC (OFNR); the minimum bend radius is 27.5mm for 3m 31.5mm for 5m 36.5.mm for 7m; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 1.5W. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.

Quality Assurance and Packaging

The completed cable is inspected at both ends, functionally tested and coiled with bend-safe slack. Protective packaging keeps the latches and boots from taking impact, while optional project labels can identify the two endpoint locations for easier field service. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Mellanox Compatibility and Factory Testing

Compatibility is verified as part of a complete installation check: connector inspection, host identification and an operating link. The physical cable is evaluated together with the expected OEM identity, because a connector that fits is not sufficient evidence that the host will accept and operate the assembly correctly. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Ordering Information

When requesting this assembly, include the exact part number and length together with the destination port types. For a rack installation, a simple port-to-port list helps us keep different lengths separate and allows any requested labels to correspond with the actual installation sequence. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QSFP-200G-2QACxxx identifies the product family; the linked page provides the final length-specific identity.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Frequently Asked Questions