Cisco SFP-H10GB-CU Compatible 10G SFP+ Passive Copper Twinax Cable

Product Highlights

• HT-manufactured compatible alternative for Cisco SFP-H10GB-CU
• 10G aggregate connectivity at 10Gbps
• Passive Twinax / Copper
• Length configurations covered: 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft), 2.5m (8ft), 3m (10ft), 4m (13ft), 5m (16ft), 6m (20ft) and 7m (23ft)
• Conductor specification: 30AWG
• Power consumption: ≤0.1W

Available Lengths and Corresponding Part Numbers

The documented configurations are 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft), 2.5m (8ft), 3m (10ft), 4m (13ft), 5m (16ft), 6m (20ft) and 7m (23ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.

Compatible OEM Part Numbers

• SFP-H10GB-CU50CM
• SFP-H10GB-CU1M
• SFP-H10GB-CU1-5M
• SFP-H10GB-CU2M
• SFP-H10GB-CU2-5M
• SFP-H10GB-CU3M
• SFP-H10GB-CU4M
• SFP-H10GB-CU5M
• SFP-H10GB-CU6M
• SFP-H10GB-CU7M

Specifications

Rack Layout and Service Access

Plan the managed route before removing the connector protection. The cable should reach both ports without tension while leaving enough space to release the latches and service adjacent interfaces. Support the run through the intended managers, keep the connector boots clear of sharp edges and avoid storing excess length in a tight coil behind warm exhaust air. For this series, keep the interface rate, DAC construction and length-specific OEM reference together throughout that review.

Applications and Deployment

Passive twinax cables are commonly selected for short switch-to-switch, switch-to-server and accelerator connections within or between nearby racks. With no separate optical conversion stage, they offer a simple low-power physical link. The assembly must nevertheless remain within the length, signaling rate and qualification limits accepted by both hosts. For this series, the listed interface is the stated interface and the aggregate rate is 10G. The stated application is 10G Ethernet.

Cable Construction and Routing

For this assembly, the conductor specification is 30AWG; the jacket material is PVC (OFNR); the minimum bend radius is 23mm; the power consumption is ≤0.1W. These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.

Quality Assurance and Packaging

The completed cable is inspected at both ends, functionally tested and coiled with bend-safe slack. Protective packaging keeps the latches and boots from taking impact, while optional project labels can identify the two endpoint locations for easier field service. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Cisco Compatibility and Factory Testing

Compatibility is verified as part of a complete installation check: connector inspection, host identification and an operating link. The physical cable is evaluated together with the expected OEM identity, because a connector that fits is not sufficient evidence that the host will accept and operate the assembly correctly. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Ordering Information

When requesting this assembly, include the exact part number and length together with the destination port types. For a rack installation, a simple port-to-port list helps us keep different lengths separate and allows any requested labels to correspond with the actual installation sequence. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number SFP-H10GB-CU identifies the product family; the linked page provides the final length-specific identity.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Frequently Asked Questions